Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Houston, TX
Gate repair in Houston means working on steel and iron in heat, humidity, and clay soil that moves more than most people realize. The city’s housing stock spans 1970s suburban driveways, 1980s Sharpstown steel gates on cracked concrete, and older inner-loop homes with narrow walkway gates and custom metalwork. Those conditions change how a gate is set, how an operator is mounted, and how long the hardware survives. We’re Portcullis Gate Repair Houston, an independently owned Kingswell company, and we handle every gate job with a written price before work starts. Call (325) 378-0676 when a gate stops doing its job.
Why Houston Homes Are Different
Houston’s lack of zoning means a gate job can sit right next to a commercial property, a townhome row, or a drainage ditch that runs heavy after a storm. That’s normal here, and it shapes how we plan the work. The bigger issue is the soil. Expansive clay expands when it rains and contracts in the heat, so concrete driveway pads crack and shift. A steel driveway gate mounted to that slab will sag within a few years, scrape the ground, and throw the post alignment out of true. We see it constantly in Sharpstown and Alief, where 1980s and 1990s homes were built with wide driveways and steel gates set directly into concrete that was never going to stay level.
Then there’s the climate. Houston’s heat and humidity rust gate hardware fast, particularly in the coastal-influenced air south and east of the city. Hinges, wheels, and actuator arms corrode quicker here than they would in a drier climate. Hurricane season adds another layer: wind loads push tall gates hard, and flood water shorts out operators and control boards mounted too low. A gate that held fine for years can fail in one storm. When we repair or install in Houston, we account for all of it: post depth, drainage, hardware grade, and where the control board sits relative to the flood line.
Styles & brands we work with
Our Main Houston Services
Houston homeowners call us most often for two things: a gate that won’t open or close, and a gate they’re ready to replace. Here’s how each works with us.
Gate Repair in Houston
A Houston gate failure is usually one of three things: a bent or sagging leaf from shifting clay soil, rusted hinges or wheels, or a mechanical part that’s simply worn out. We start by finding the actual cause, then quote the fix in writing before we turn a single bolt. On homes in the older inner-loop neighborhoods, we often find narrow walkway gates with historic metalwork that needs custom-matched repair rather than an off-the-shelf replacement. Gate Repair in Houston covers the whole scope: hinges, posts, wheels, latches, and alignment.
Gate Installation in Houston
New gate installations in Houston have to contend with the soil and the driveway slope. We set posts deeper than minimum spec where we can, and we account for drainage so water isn’t pooling against the post base. That matters on 1970s suburban homes with wide driveways and on newer build sites where the grade hasn’t settled yet. Whether it’s a steel driveway gate or a custom walk gate, the job gets measured, quoted, and scheduled with a written price. Gate Installation in Houston covers the full process from measure to final walkthrough.
Electric Gate Repair in Houston
Houston’s storms and humidity are hard on electric gate systems. Control boards flood, solar panels underperform in overcast weeks, and wiring connections corrode. The actuator, which is the motorized arm that physically pushes the gate open, takes the brunt of daily use and Houston heat. When a gate won’t respond to the remote or keypad, it’s usually the actuator, the board, or a bad connection. Electric Gate Repair in Houston covers diagnostics, board replacement, actuator swaps, and wiring repairs, with a written price before work begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Houston
Our Houston technicians carry parts for the operators most common in this market, including LiftMaster, FAAC, BFT, and Linear. Because we stock locally, we can often complete a board or actuator swap on the first visit. See our brands for the full list of systems we service.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Houston, TX
| Service | Typical range in Houston |
|---|---|
| Gate alignment and sag correction | $180 – $340 |
| Hinge or wheel replacement (parts and labor) | $140 – $280 |
| Swing-gate actuator swap | $450 – $820 |
| Control board replacement | $280 – $560 |
| Photo-eye sensor replacement or realignment | $110 – $250 |
| Keypad or receiver replacement | $130 – $300 |
| Steel driveway gate installation (per leaf) | $1,900 – $4,800 |
| Walk gate installation | $650 – $1,900 |
| Electric operator installation (parts and labor) | $1,200 – $3,100 |
| Full gate system installation (gate, operator, safety edges) | $3,400 – $8,900 |
Houston’s soil and rust conditions can push a job toward the upper end of these ranges: a sagging gate that needs post resetting, a control board with corrosion damage, or a driveway slab that needs grinding all add labor. What never changes is the price promise. We give every quote in writing before the work starts, and that’s the number on the invoice. No Houston heat-of-the-moment adjustments, no surprises at the door.
Neighborhoods We Serve in Houston
We dispatch from our Houston office and cover the full metro area. Most Houston calls get a same-day or next-day response window, and we give you a real arrival window before the truck rolls, not after. Here’s a sample of where we work regularly:
- Sharpstown
- Alief
- Kingwood
- Clear Lake
- The Heights
Service Area – Cities Near Houston
Beyond Houston proper, we also serve the surrounding cities where gate jobs come in weekly. If your gate is in Pasadena, TX, South Houston, TX, Bellaire, TX, or Friendswood, TX, the same written-price standard applies. Send us the details and we’ll give you a straight number.
Serving Houston, TX - Our Local Coverage Area
We’re based in the Houston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Houston
Most Houston calls get a same-day or next-day response window. We give you the arrival window when you book, and a live person answers the phone around the clock, including holidays. Call (325) 378-0676 and we’ll tell you when we can be there, no voicemail trees.
It depends on the neighborhood and the scope. Many Houston HOAs, especially in master-planned communities, have design rules for gates and fence heights. The City of Houston permits certain structural work. We’ll tell you what applies to your property before you commit to the job.
The Kingswell Guarantee covers four things on every job: a written price before work starts, a real arrival window, a clean job site, and a written guarantee on the repair. The guarantee runs 365 days, and if the repair fails inside that period, we come back and fix it at no charge. That’s the 365-Day Done Right Promise, stamped on the invoice.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Houston Customers Say
"The gate works great now. Only thing is the first tech couldn't find the wiring fault and they had to send a second guy the next day. Second visit nailed it and they didn't charge me twice."
- Chuck Alderman"Good repair on a sagging gate and a new hinge welded on. Took them a couple days to get the part in, but they told me that up front and it's been solid since."
- Hector Villanueva"Gate was dragging and screeching across the driveway. I figured I'd need a whole new setup. He adjusted the track and rollers and it was a fraction of what I expected. Honest work."
- Omar Haddad