Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Houston Homeowners
A gate that won’t open, sags on its hinge & post repair needs, or grinds halfway and stops isn’t just an annoyance – it’s a broken barrier between your home and the street. Portcullis Gate Repair Houston has fixed thousands of gates across Harris County since 2008, from cantilever slides in Kingwood to wrought iron swing gates in West University Place. Most driveway gate repairs run $180 to $1,200 depending on what’s failed, and we quote that price in writing before any work starts. Call (325) 378-0676 and you’ll reach a live person, not a voicemail tree. We’re a Kingswell company, which means every repair carries the 365-Day Done Right Promise: if it fails within a year, we come back free.
Driveway Gate Repair
Driveway Gate Repair is what we do most often in Houston – fixing the gate that guards the entrance to your home, whether it swings on hinges or slides on a track. The most common failures we see in this climate are actuator motors burned out from the humidity, control boards fried by summer lightning strikes, and steel posts loosened in our expansive clay soil. A basic hinge replacement or gate realignment typically runs $180 to $400. A full actuator swap, where we replace the motorized arm that physically moves the gate, usually lands between $650 and $1,200 parts and labor. Every job gets a written price before we touch a bolt, and the repair is guaranteed in writing for 365 days.
Actuator and motor replacement
The actuator is the motorized arm that pushes a swing gate open and pulls it closed. Houston’s heat and humidity are hard on these motors, and when one fails, the gate usually won’t move at all or moves in short, jerky bursts. We service LiftMaster, FAAC, BFT, and Linear actuators, and we arrive with the right replacement on the truck so the gate is working again in one visit.
Hinge and post repair
Clay soil in Houston expands when wet and contracts when dry, which slowly works gate posts loose until the gate sags and drags on the driveway. We reset posts in new concrete, and we install heavier hinges when the old ones have worn their pivot points oval. This is often a same-day fix when the post itself is still sound.
Styles & brands we work with
Gate Welding
Gate Welding is the structural repair work that happens when a metal gate cracks, snaps, or tears loose at a joint. This is common on older steel gates where the weld holding a hinge plate to the frame gives out, or where a heavy gate has been hanging on undersized posts for years. Weld repairs in Houston typically run $150 to $450 per crack or broken joint, depending on access and how much grinding and preparation the area needs. A full re-weld of a gate frame with new gussets and reinforcement plates usually lands between $500 and $1,500. We quote the exact number in writing after we see the damage, and that number doesn’t change.
Cracked frame and joint repair
A crack in a gate frame usually starts small and grows fast, especially on a gate that gets opened several times a day. We grind out the crack, weld it solid, and often add a reinforcing plate so the same spot doesn’t fail again. The repair is ground smooth and painted to match so you can’t tell where the weld was.
Hinge plate and bracket rewelding
When a hinge plate tears away from the gate frame, the gate drops and starts dragging. This is a structural failure, not a hinge problem, and it needs welding, not a wrench. We cut the old plate off, clean the frame, and weld a new plate in place, then hang the gate and set the gaps.
Commercial Gate Repair
Automatic gate repair for commercial properties covers the sliding and swing gates at apartment complexes, office parks, warehouses, and gated communities across Houston. These gates cycle dozens or hundreds of times a day, and when one goes down, it backs up traffic and leaves the property open. Most commercial operator replacements in Houston run $1,200 to $4,000 depending on the operator type and whether the gate itself needs structural work. We also handle safety edge replacement, loop detector repair, and photo eye realignment, usually for $250 to $800. Every commercial job includes a written price and a written guarantee through the Kingswell Guarantee, and we schedule around your property’s traffic patterns.
Operator and control board replacement
The operator is the motor and gearbox that drives a sliding or swing gate, and the control board is the brain that tells it when to run. On a busy commercial gate, both wear out from sheer duty cycles. We replace operators from LiftMaster, FAAC, BFT, Linear, and DoorKing, and we program the limits, timer, and safety loops before we leave.
Safety system repair and testing
Commercial gates in Houston must have working safety edges and photo eyes, and a gate that reverses on a car or a person is a liability for the property owner. We test every safety circuit with a force gauge after a repair, and we replace worn edge sensors and misaligned eyes as part of the job. The written guarantee covers the full system, not just the part we replaced.
Iron Gate Repair
Iron Gate Repair covers gates made from solid iron or steel, including the ornamental gates you see on older Houston homes in the Heights and Bellaire. These gates are heavy, and they fail in predictable ways: hinge pins wear, welds crack at stress points, and the bottom rails rust from standing water. Simple hinge pin replacement on an iron gate usually runs $150 to $350. Structural work like straightening a bent rail or rewelding a cracked frame joint lands between $300 and $900 depending on the size of the gate and how hard it is to get at the damage. We match the finish so the repair doesn’t stand out.
Rust repair and reinforcement
Houston’s humidity means an iron gate without good paint is slowly rusting, usually from the bottom rail up. We cut out rusted sections, weld in fresh steel, and reinforce thin spots with plate before priming and painting. The repair is built to look original and to outlast the rest of the gate.
Hinge pin and pivot rebuild
An iron gate that squeals and drags usually has worn hinge pins or egged-out pivot holes. We rebuild the hinge barrels with new pins and sometimes new bushings, which takes the play out of the gate and lets it swing true again. This is the fix that makes an old gate open like it did when it was new.
Sliding Gate Repair
Sliding Gate Repair is the service for gates that roll sideways on a track instead of swinging on hinges, and Houston has thousands of these on both homes and commercial properties. The three failures we see most are bent or clogged tracks, worn rollers, and broken chains or belts on the operator. Roller replacement on a residential slide gate typically runs $250 to $600. Track repair or replacement, including concrete work when the track has settled, usually lands between $500 and $1,500. A new chain or belt for the operator is $150 to $350. We quote each of these in writing before starting, and the repair is guaranteed for a full year.
Track and roller service
Houston’s clay soil shifts, and a sliding gate track that was flat five years ago may now have a hump in it that lifts the gate off its rollers. We survey the track, shim and re-level where possible, and replace crushed or worn rollers. A gate that rolls smoothly again puts less strain on the operator and the frame.
Chain, belt, and limit switch repair
The chain or belt is what connects the slide gate operator to the gate itself, and when it snaps or jumps a tooth, the gate stops moving. We replace chains and belts and reset the limit switches so the gate opens fully and closes fully without slamming the end stops. This is routine work for us, and it’s usually done in one visit.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is the specialty work for decorative gates with ornamental scrolls, pickets, and forged details, the kind you see on older Houston homes in the Heights, Bellaire, and River Oaks. These gates are as much a visual feature as a security barrier, so the repair has to be strong and invisible. Straightening a bent picket or scroll typically runs $100 to $300 per section. Replacing rusted-through bottom rails or rebuilding a sagging corner costs $350 to $900. We match the gate’s original profile and paint so a repaired section blends with the rest of the gate.
Picket and scroll replacement
Individual pickets and decorative scrolls get bent by impacts and rust thin from Houston’s rain and humidity. We hand-cut replacements to match the existing profile, weld them in, and finish them to match the gate. The result is a repair you can’t find without someone pointing it out.
Sag correction and frame reinforcement
A wrought iron gate that drags has usually lost the fight with gravity and its own weight. We jack the gate level, weld in reinforcement plate and gussets where the frame has flexed, and reset the hinges. The gate ends up stronger than it was originally, without changing the look.
Metal Gate Repair
Metal Gate Repair is the broad category covering steel, aluminum, and iron gates of every style, including modern aluminum frame gates with composite panels. Aluminum gates fail differently than steel ones: the extrusion cracks at weld points and the gate racks out of square. Steel gates rust and sag. A brace repair or crack repair on a metal gate in Houston typically runs $180 to $500. Full rewelding of multiple joints and hardware replacement lands between $450 and $1,200. We tell you exactly what’s wrong, what it costs to fix it correctly, and what we’d do if it were our gate. That written estimate is yours before you decide anything.
Aluminum frame repair
Aluminum gates look clean and modern, but their welded corners crack from repeated flexing and hard slams. We weld the cracked sections back solid and install corner gussets that spread the load across the frame. This stops the gate from racking and keeps the original appearance.
Steel post and frame straightening
A steel gate that’s been hit by a car or blown open by a storm can bend the frame or the post enough to throw the gate out of alignment. We straighten frames cold where the steel isn’t cracked, and we replace posts that are bent past the point of being safe to reuse. The gate ends up plumb, level, and latching like it should.
Wood Gate Repair
Wood Gate Repair covers the cedar and pine gates found on Houston homes with wooden fences, especially in neighborhoods like Tomball, Friendswood, and Rosenberg. Wood gates fail from moisture, termites, and simple age: the frame rots, the boards warp, and the hinges pull out. Replacing hinge hardware and reinforcing a soft frame post typically runs $200 to $500. A full rebuild of a single wood gate with new frame lumber and boards usually lands between $450 and $900. We build with pressure-treated or cedar stock that lasts in Houston’s wet heat, and we quote the full price in writing before we start.
Frame and brace replacement
The frame is the rectangle of lumber the gate boards are nailed to, and when it rots from the bottom up, the whole gate sags. We cut out the rotted rails and stiles, install new pressure-treated lumber, and add a diagonal brace so the gate can’t rack. The boards go back on straight and the gate swings square.
Hardware retrofit and sag fix
Most wood gate sag comes from weak hinges and a missing or broken brace, not from bad wood. We install heavier hinges with longer screws that bite into good material, add an anti-sag kit where it’s needed, and adjust the lock repair if needed. The gate stops dragging and actually latches without lifting the handle.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
Our technicians are certified on nine major gate operator brands, and we stock OEM parts for the ones we see most often in Houston: LiftMaster, FAAC, BFT, and Linear. On a LiftMaster swing or slide operator, we replace the motor, gearbox, and control board with factory parts, and we program the limits and force settings to the gate’s actual weight. On FAAC and BFT hydraulic and electromechanical operators, we rebuild rams, replace seals, and bleed hydraulic lines so the gate moves smoothly again. Linear operators are common on older Houston systems, and we keep their boards and radio receivers on the truck.
We also service Ghost Controls, Viking, DoorKing, Elite, and Mighty Mule. Whether you know exactly which brand is on your gate or you’ve never looked at the motor housing, the technician who arrives will identify it, explain what’s failed, and quote the repair in writing before starting. If you know the brand when you call, tell us and we’ll make sure the right parts are on the truck.
Signs You Need a Pro Right Now
- The gate stops halfway and reverses. This usually means a safety sensor is blocked or a force setting has drifted. It can also mean the gate has hit something and bent a wheel or roller. A gate that won’t complete its cycle is a gate that won’t keep anything out.
- The gate is sagging and dragging on the driveway. A dragging gate puts a huge load on the operator, the hinges, and the frame. The longer it runs like this, the more parts fail. This is the kind of repair that gets more expensive the longer it waits.
- The operator hums but the gate doesn’t move. That hum is the motor trying to drive a gearbox that’s stripped or a ram that’s lost pressure. Running it this way burns out the motor, which means a $300 part turns into an $850 replacement.
- The gate slams closed or bangs against the end stops. Slamming means the limit switches or soft-close settings have failed, and every slam hammers the frame and hardware. Left alone, a slamming gate will eventually crack a weld and drop off its hinges.
- You can hear metal grinding or squealing during travel. Grinding is metal on metal: a seized roller, a dry hinge pivot, or a gearbox eating itself. Squealing is the same problem earlier in its life. Both are warnings, and both are cheaper to fix before the part fails completely.
Our Process, Step by Step
- 1
You call and talk to a live person. Someone at Portcullis Gate Repair Houston answers the phone 24/7, including holidays. You describe what the gate is doing, and we schedule a window that works for you – and we actually arrive in that window.
- 2
The technician diagnoses the failure. We test the operator with a digital multimeter, check the amp draw on the motor, verify the safety sensors with a force gauge, and inspect every hinge, roller, weld, and bracket. We look for the root cause, not just the symptom.
- 3
You get a written price before any work starts. The number on the estimate is the number on the invoice. It covers parts, labor, and any hardware or paint needed to complete the repair. If we find something hidden, we stop and talk to you before doing anything else.
- 4
The repair is completed and tested. We make the fix, then cycle the gate through full open and close cycles while checking the limits, the safety reversal, and the auto-close function if you have one. We leave the job site cleaner than we found it – no cutoff wheels, no weld slag, no hardware on the ground.
- 5
You get the Kingswell Guarantee in writing. Every repair invoice carries the 365-Day Done Right Promise. If the gate fails within a year, we come back and fix it at no charge. That’s not a promise over the phone – it’s stamped on your invoice.
How Much Does Gate Repair Cost in Houston?
A typical gate repair in Houston runs $180 to $1,200, with most jobs landing between $300 and $800. A simple hinge pin replacement or sensor adjustment is at the low end, around $150 to $350. A full operator motor and gearbox replacement, common on older LiftMaster and FAAC units, usually runs $700 to $1,200. Structural work like welding a cracked frame or rebuilding a sliding gate track runs $500 to $1,500 depending on the size of the gate and the condition of the surrounding concrete. A complete new operator with installation on a residential gate typically lands between $900 and $2,200.
Three things move the price: the type of operator, the condition of the gate itself, and whether the failure is mechanical or electronic. A gate that’s been neglected for years always costs more to fix because multiple things have given out at once. The easiest way to avoid overpaying is to get a written price before work starts, and that’s what we do on every single job. Our estimates are free, they’re detailed, and they don’t change once you approve them. Call (325) 378-0676 and we’ll give you an exact number, not a range over the phone.
Our Service Area Near Houston
Portcullis Gate Repair Houston serves the entire Houston metro, including Gate Repair in Pasadena and Gate Repair in League City. We also run calls to Missouri City, West University Place, Tomball, Friendswood, Rosenberg, Dickinson, Bellaire, Santa Fe, and Jersey Village. Most Houston customers are scheduled within 24 to 48 hours, and emergency calls are dispatched the same day. Our home page has more about the Kingswell Guarantee and the full list of services we offer.
Serving Houston, TX - Our Local Coverage Area
We’re based in the Houston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Houston
Gate repair is the work of diagnosing and fixing a gate that won’t open, won’t close, sags, makes noise, or has failed structural or electrical components. It covers everything from hinge pins and rollers to operator motors, control boards, safety sensors, and welded steel frames. On a Houston gate, repair usually means making the gate operate smoothly and safely again without replacing the whole system.
Most residential gate repairs are completed the same day, usually within one to three hours on site. Structural welding work or a full operator replacement can take four to six hours. We’ll tell you the expected time before we start, and we don’t leave until the gate is tested and working.
Most gate repairs in Houston run between $180 and $1,200. Simple hardware repairs cost less, while operator motor replacements and structural welding cost more. You’ll get an exact written price before any work starts, so the number you approve is the number you pay. Call (325) 378-0676 for a free estimate.
Yes, we service LiftMaster operators regularly across Houston. Our technicians are certified on LiftMaster systems, we stock their OEM parts, and we can replace motors, gearboxes, control boards, and safety sensors. We also service FAAC, BFT, Linear, and five other major brands.
Yes. We take emergency calls 24 hours a day, 7 days a week, and a live person always answers the phone. If your gate is stuck open and you can’t secure the property, or stuck closed with a car trapped inside, we dispatch a technician the same day. Call (325) 378-0676 and tell us what’s happening.
Every repair we make in Houston carries the 365-Day Done Right Promise, which is part of the Kingswell Guarantee. The guarantee is written on your invoice, and it means if the repair fails within one year, we come back and correct it at no charge. That includes a free return visit, no hidden fees.
Clear the area around the gate so our technician can work, and make sure the gate’s power source is accessible. If you know the brand of your operator, have that ready when you call so we can bring the right parts. You don’t need to take anything apart or diagnose the problem – that’s our job.
Schedule Your Gate Repair Service in Houston Today
A gate that’s down leaves your property open and your routine broken. Call Portcullis Gate Repair Houston at (325) 378-0676 for a free, no-obligation estimate. A live person answers around the clock, we arrive in the window we give you, and you’ll have a written price and a written 365-day guarantee before the work begins.
Written by Dean Prescott, Owner at Portcullis Gate Repair Houston, serving Houston since 2008.